Versions Compared

Old Version 20

changes.mady.by.user Julian Słowiński (Unlicensed)

Saved on

compared with

New Version Current

changes.mady.by.user Joanna Kozakiewicz

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Wireless ZigBee Button is a button switch which ZIGBEE GREENPOWER is a switch that is designed for use in the Glamox Wireless ZigBee system.

No wiring and lack of power connections give wide possibilities of for mounting. Installation is easy and the device does not require maintenance. The device also does not need an internal battery or any external power supply. Energy The energy source is an electro-dynamic energy generator inside the switch.

The comfort of the usage is very high due to the low mechanical force needed for pressing the buttons.
In addition to conventional ON/OFF control, you can use this button for dimming the light and triggering lighting scenes.

Product page onGlamox website

LMS ZIGBEE GREENPOWER 2B

Image Removed

LMS ZIGBEE GREENPOWER 4B

Item requires additional frame:

https://www.glamox.com/en/pbs/products/light-control/wireless-solutions/b12202005/

Image Added

https://www.glamox.com/en/pbs/products/light-control/wireless-solutions/b12202002/

The switch requires an additional frame

Image Added

https://www.glamox.com/en/pbs/products/indoor/downlight/1411701/

Device features

No battery and no wiring

  • Gluing or screwing onto the flat surface

  • ON/OFF, dimming, scene control (4B only)

    • Drawio sketch
    zoom1
    simple0
    inComment0
    custContentId2261876745
    pageId2240675841

    custContentId2261876745

    lbox1
    diagramDisplayNameJumitech_instruction
    contentVer6
    revision6
    baseUrlhttps://glamox.atlassian.net/wiki
    diagramNameJumitech_instruction
    pCenter0
    width816
    links
    tbstyle
    height378

    Commissioning procedure

    For commissioning a switch, follow the steps shown in the app.

    Limitations - how

    How to use it in the LMS design

    Range: within one room (up to 10m line of sight),

    Limitations

    • See system limitations dictated by the sensor.

    • Add all luminaires in a group first and then add a switch. Switch The switch binding mechanism is to each node within the Zigbee group at the time of commissioning. If new nodes are added after commissioning, switch binding does not take place.

    • A switch can be added either to a group or to a zone. Once added to a zone, another switch will need to follow the same choice i.e. either a group or a zone.

    • Up to 5 switches can be added within a group. All switches attached within a group should belong to a single brand. Combining switches from different brands is not recommended.

    • In case switches are used for a group and at the same time for zones of that group, three things need to be taken into account:

      • The switch of the group should be added first.

      • Only 2-button switches should be used for the group.

      • In the zones, 4-button switches with scene setting settings can be used.

    • It is recommended to use not more than one 4-button switch per zone.

    • If two or more zones are used with a 4-button switch, the maximum number of lights is 20 per zone.

    • In case the switch is not detected during the commissioning procedure, please re-try.

    • The switch needs to be mounted so that “I” is at the TOP and “O” at the BOTTOM (check the picture).

    • It is only allowed to use switches / input units from one supplier in one group.

    • During the commissioning of ZGP switches (in test setups) the devices should not be too close to the lights (between 2m and 5m distance) to avoid commissioning failures.

    How to commission it?

    For commissioning a switch, follow the steps shown in the app.

    Adding switches (panels)