Connect the gateways to power and ethernet
If DALI gateway, also connect DALI line(s)
Connect the access point to 24V power and ethernet
Make sure the access point has access to the network where the gateways are connected
Only the access point speaks to the Glamox Connect cloud. The access point communicates with all gateways and administer the two-way communication between the gateways and the cloud
Check the serial number on front of access point (5 digits)
Go to URL http://GlamoxConnectCore<serial>.local, for example http://GlamoxConnectCore30288.local if the serial is 30288
Make sure that the IP addresses of the gateways will be consistent, either by IT binding the mac address to an static IP (recommended) or by assigning static IP
The Access point WebUI from 5. will list all gateways on the network with current settings
as long as multicast is enabled in the network
For Wireless Zigbee, log in to the web ui of the gateway to set IP if needed
For Ethernet2Dali, use Firestarter app to set up IP addresses of gateways
For DALI Complete you need to use an external tool, as the DALI gateway does not provide any WebUI
Recommended to use free software like for example Lantronix - Device installer
If Glamox Wireless Zigbee the gateway needs to be set up with an access code to connect access point to the gateway
Make sure to be on same local network to reach the gateway
Follow gateway manual to go to admin page, default http://192.168.0.211
You can also find the local url (with link) from the access point WebUI
Go to Security tab and activate “Access code”
Use access code 1337 (default for the gateway integration) or the access code part of the QR code on back of gateway.
Press “Activate” to allow for new connections for 5 minutes. The gateway integration needs to start within these 5 minutes. If successful you will see the access point connected to the gateway.
This needs to be coordinated with LMS Team (for now). If all the integrations are setup the access point will try to join after reboot.
Contact the LMS team if the synchronization and joining is not succesful
...
Network setup
Multicast (optional, access point to discover gateways)
DHCP (optional)
Internet access
Port | Protocol | What |
|---|---|---|
8883 | TCP | AWS MQTT |
8443 | TCP | AWS Calls |
1883 | TCP | AWS MQTT |
443 | TCP | AWS Calls |
Any port | UDP | Access point upgrade, reporting++ |
| Note |
|---|
We HIGHLY recommend isolating the lighting components in a own network, without access to other components at your internal network setup. Glamox gateways only needs to be discoverable and reachable from access point Access point(s) needs to communicate with gateways, as well as the Glamox cloud servers |
Finding a device from the mac address
...
Make sure you are connected to the same network as the device. Then open a terminal (for example Command Prompt on Windows). Type in “arp -a” and you will get a list of devices with their IP and mac address (physical address).
Find the IP address (internet address) related to your MAC address
...
DALI complete gateway
To change the IP on the DALI gateway, use a free tool like Lantronix (https://www.lantronix.com/products/deviceinstaller/). Make sure you are connected to the same network and search for devices.
...
The gateway has pullout panels on top and bottom of the front. Here you can find detailed information about the gateway like the mac address.
Wireless Zigbee gateway
The Zigbee gateway has a WebUI for easy setup. This WebUI can be reached from your access points WebUI at http://GlamoxConnectCore<serial>.local
...
Note: USB 4G modems that acts as a network interface, without PIN code, can work. Try on your own machine to verify no drivers are needed, and the dongle acts as a normal network interface (no special software required)
Network requirements
...
)
...
DHCP (optional)
...
Internet access
...
Port
...
Protocol
...
What
...
8883
...
TCP
...
AWS MQTT
...
8443
...
TCP
...
AWS Calls
...
1883
...
TCP
...
AWS MQTT
...
443
...
TCP
...
AWS Calls
...
Any port
...
UDP
...