Necessary components
...
LMS WIRELESS DONGLE INC SOFTWARE
...
Tablet - Samsung Galaxy Tab (2, 3, 4, E, A, A 10.5)
First Time Connection
...
Connecting a DONGLE
Necessary components
...
Step by step instructions
To connect a new DONGLE to the tablet
...
select the Bluetooth Icon [1] and select 'LiteIPMate' from the drop down menu [2].
...
Click Find New Device.
...
Press OK to accept the Pairing Code.
When Paired DONGLE will Automatically Connect
...
Connection is confirmed by Bluetooth icon changing from Grey to Blue
...
...
| Info |
|---|
If you are connecting a BLE DONGLE, please select ‘GlamoxDongle’ from the drop menu and select 'no' when asked to include MicroSet. |
The app will start scanning for the nearest DONGLE(s) and will display them in a list [3]. This may take 20 seconds to a minute.
...
Look on the back of the DONGLE to find the matching MAC address and click ‘Connect’ on the correct DONGLE in the app list [4].
...
Once the DONGLE has connected, the Bluetooth icon will change from Grey to Blue.
...
| Info |
|---|
If it doesn't connect:
|
...
If Mac address is ‘None’ or different to DONGLE then re-pair as left.
| Info |
|---|
(*) No longer applies from v.3.121 onwards. |
Standby Mode
To Wake Up
Move the device through more than 180°. Green LED Lights.
Running On Internal Battery
Device goes back into Standby after 3 minutes If Bluetooth not connected.
Device goes into standby if no movement or activity for 15 minutes.
Plugged into USB on Slow Charge
Goes to sleep after 15 minutes without activity (allowing faster charging) (*).
Plugged into USB on Fast Charge
Stays on indefinitely.
| Info |
|---|
(*) No longer applies from v.3.121 onwards. |
Working Offline
Either switch the DONGLE off manually or:
...
Click the Bluetooth icon.
...
| Info |
|---|
The Mac address of the DONGLE is on the label on the back of the device. |
Manual Switching
Switch On
Press pin in small hole once, red LED illuminates briefly.
Press again, green LED illuminates briefly.
| Info |
|---|
See LED Statuses section for more detail |
Switch Off
Press pin in small hole once, red LED illuminates briefly.
Press again, green LED goes out.
| Info |
|---|
It is not normally necessary to manually switch the device off unless it will not be used for several weeks. |
Charging
Switched On
Unit is charged by connecting to a USB port in a PC or charging socket.
Slow Charge (100 mA) - Green LED flashes twice every 2 seconds.
Fast Charge - Green LED flashes three times every 2 seconds (*).
Fully Charged - Green LED is ON and stops flashing.
| Info |
|---|
From v.3.121 onwards charging will always use the full capacity of the charger. Therefore, do not use with a USB 1 socket in a laptop/PC as this could damage the USB socket. |
| Info |
|---|
(*) No longer applies from v.3.121 onwards. |
Switched Off
No charging takes place if the device has been manually switched off.
LED Statuses
...
Status
...
Activity
...
Green LED
...
Off
...
Manually switched off or in standby
...
2 flashes
...
Charging at 100 mA
...
3 flashes
...
Charging at 500 mA
...
10 second flash
...
Fully charged in standby (*)
...
1 second cycle
...
Running on internal battery
...
On
...
Fully Charged and Active
...
Red LED
...
4 second flash
...
Running on battery but battery getting low.
...
10 second flash
...
Asleep and battery getting low (*).
IF MAC address starts with 10:**:**:**:**, THEN first two characters are 60:8A Otherwise, IF MAC address starts with 66:**:**:**:**, THEN first two characters are 00:06 |