| Note |
|---|
NOTE: Setting of IP on gateways is not yet possible to do on site, without special software. If your system engineer does not have this software and training, the IP’s need to be set up before the gateways are installed |
Connect the gateways to power and ethernet
If DALI gateway, also connect DALI line(s)
Connect the access point to 24V power and ethernet
Make sure the access point has access to the network where the gateways are connected
Only the access point speaks to the Glamox Connect cloud. The access point communicates with all gateways and administer the two-way communication between the gateways and the cloud
If needed, change the IP’s of the gateways to preferred IP address (See note!)Check the serial number on front of access point (5 digits)
Go to URL http://GlamoxConnectCore<serial>.local, for example http://GlamoxConnectCore30288.local if the serial is 30288
Make sure that the IP addresses of the gateways will be consistent, either by IT binding the mac address to an static IP or by assigning static IP
The Access point WebUI from 5. will list all gateways on the network with current settings
If Glamox Wireless Zigbee the gateway needs to be set up with an access code to connect access point to the gateway
Make sure to be on same local network to reach the gateway
Follow gateway manual to go to admin page, deafult default http://192.168.0.211
Make sure to be on same local network to reach the gatewayYou can also find the local url (with link) from the access point WebUI
Go to Security tab and activate “Access code”
Use access code 1337 (default for the gateway integration) or the access code part of the QR code on back of gateway.
Press “Activate” to allow for new connections for 5 minutes. The gateway integration needs to start within these 5 minutes. If successful you will see the access point connected to the gateway.
The IP’s and access code are given to the Glamox Connect installer
- NOTE: In the future this will be available in the admin interface for the customer
This needs to be coordinated with LMS Team (for now). If all the integrations are setup the access point will try to join after reboot.
Contact the LMS team if the synchronization and joining is not succesful
| Info |
|---|
This process is under development. The process will be more and more automated, allowing the installers to do all steps in an easy fashion. |
Finding a device from the mac address
If your access point can’t find the gateways the main issue is probably that they are not on the same network. If you are sure this is not the case, you can try to connect to the network yourself and search for devices.
Make sure you are connected to the same network as the device. Then open a terminal (for example Command Prompt on Windows). Type in “arp -a” and you will get a list of devices with their IP and mac address (physical address).
Find the IP address (internet address) related to your MAC address
...
The gateway has pullout panels on top and bottom of the front. Here you can find detailed information about the gateway like the mac address.
Zigbee gateway
The Zigbee gateway has a WebUI for easy setup. This WebUI can be reached from your access points WebUI at http://GlamoxConnectCore<serial>.local
Follow gateway manual to go to admin page, default http://192.168.0.211.
You can change the network settings of the gateway under “Network settings”.If you can’t find the IP of the gateway, search for the gateways mac address on the network.You can find the mac address of the gateway on the back of the gateway.
Access point
The access point is a linux computer, in the form of a Kunbus RevPi Core 3+. This is a industry grade Raspberry Pi 3+ compute module, running a customized linux distribution.
The device is set up to receive IP via DHCP. To set up static IP, contact Glamox technicians.
...
| title | Not implemented yet |
|---|
It is set up with DHCP, and fallback on static IP. If network is no set up with DHCP, you can reach it by using IPv6 and mDNS. Connect to the same network with your device and point your browser to glamoxconnect.local. Here you can set the device static IP.
E.g:
...
go to the access point webUI at http://GlamoxConnectCore<serial>.local
There you can set the access point IP, network mask, gateway and name servers
...
| Info |
|---|
The IP settings of the Access point is of no importance to Glamox Connect. Only the gateway IP’s are important in the setup |
For Glamox technicians to reach the device, it is set up with ZeroTier. This requires UDP 9993 to be open out of the network. If the network is set up with DHCP, it will automatically connect, and the technicians can reach the device. As a fallback, a USB 4G modem can be connected to bypass any firewalls while setting up the system.
...